Whether you’re in a brand new house or enjoying your home’s jubilee year, there are probably a few minor repairs or electrical issues needing attention. Some problems will need a professional, while others can be addressed by anyone with a screwdriver and some attention to detail. Even electrical work has a few home-wiring quick fixes that are safe and simple to follow. Quick fixes like this can not only save you on costly repairs, but they’ll also help you to identify any further problems that do require professional assistance.
Not Enough Outlets
While modern homes feature far more outlets, also known as electrical receptacles, older homes often have only one or two outlets within a room. For a low-cost quick-fix, extension cords and power strips are the obvious choice. Any cords and cables you use should be able to safely handle the electrical loads you place on them. To ensure this, use a lower number gauge (a thicker wire) for your cords and power strips. We recommend at least 14-gauge cable.
Unfortunately, extensions and power strips can get unsightly very quickly. For private rooms with low foot traffic this fix is fine; larger rooms with a high number of visitors will want something that’s less likely to become an eyesore. When power strips are an eyesore, adding additional electrical outlet receptacles is ideal. New receptacles should only be installed by licensed electricians to ensure that your wiring remains up to code. Of course, new wiring will need to be run and additional holes will be cut into existing walls to account for the new outlets, which is why you always want a properly trained electrician.
A more minor problem, again with outlets, requires a physical inspection first. Some outlets are installed with wires pushed into simple slots in the back of the receptacle. While there’s nothing wrong with this system, vibration, heat expansion, and aging can cause these connections to slide out over time. It’s a very simple fix to simply pull the wire free of the terminal and use the more traditional screw-terminal for added security.
Plugs Fall Out of Existing Outlets
As electrical sockets age, the metal contacts loosen due to repeated use. It becomes an obvious problem when plugs slide out of sockets simply because of gravity. This often leads to incomplete connections, turning off electronics and leading to failed charge cycles for phones or batteries. Some of these loose connections can lead to excess carbon build-up inside the socket due to arcing between the contacts; a possible safety hazard. For these reasons, a sagging plug is a key signifier that it’s time to replace your outlet.
Replacing an outlet is much easier than installing new ones, and can usually be done with a simple technical guide and a few tools.
With so many USB-powered devices arriving, it may not be a bad idea to go ahead and upgrade to an outlet which includes a few USB ports already either.
Whenever a bulb’s wattage requirement exceeds the maximum rating for a fixture you’re faced with a problem known as overlamping. While your building’s wiring may fully be capable of handling the higher wattage demanded by the bulb, if your fixture or socket is rated for the power drawn by then light bulb, it can overheat leading to burnt insulation or a melted socket. Because of how dangerous overlamping can be it is a code violation and something you should fix immediately. If you’ve noticed that the fixture, socket, or even the light switch you use is getting excessively warm, you should double check the wattage rating for those components.
The cheapest way to fix this problem is to replace the bulb in your fixture. If your fixture uses multiple light bulbs, make sure that the total wattage of all the bulbs is lower than the maximum rating for your fixture. Then again, if you like the amount of light offered by higher-wattage bulbs you should consider purchasing a new fixture or socket with a higher wattage rating or switch to more energy-efficient lights such as CFLs or LEDs. So long as the total wattage consumed by the bulb is less than the rating of your fixture, you’ll be fine.
Flickering lights can be caused by many problems, some of which are easy to fix while others require expensive repairs. Some of the more common faults are as follows:
- Bad or Aging Fluorescent Ballast – A fluorescent ballast regulates the electrical voltage or current travelling to your lights. As the ballast ages, it becomes less efficient at doing this, which can lead to flickering lights and decrease lamp-life.
- Faulty Switches – Loose light switches or dimmers can create incomplete connections or faulty current flow to your lights. If you use incandescent lights, a faulty switch is often the cause.
- Bad Wiring – Flickering lights can also be a sign of faulty wiring or loose terminal connections. If the source of the flickering lights is not readily apparent, it’s best to get an electrician to examine your home’s wiring to make sure there isn’t some other damage or loose electrical connection at fault. Bad wiring is dangerous and should be dealt with as soon as possible.
While these five issues are fairly simple to fix, if you find yourself in over your head you should always call a professional. Electrical work can be dangerous which is why we’re always ready to lend a hand when you need it. For any major work you should always call a certified technician.
For more Tips regarding electrical issues and safety check out:
Give us a call at (302) 368-3848 for any of your home service needs — plumbing, electrical, HVAC, propane, and more! We are available 24 hours a day, 7 days a week to answer any questions you might have.
If you want to know more about maintaining a safe and efficient home, follow us on website, Facebook, Twitter, and Google+.